Compare 
Sign inProduct decision guide · Robot finishing tools
LX-F40-S1-A Compliant Grinding Spindle
LX-F40-S1-A: evaluate the 1 kW spindle, 0.6 Nm listed torque and 4.2 kg tool against access, compliance direction, drive scope and a measured finishing trial.
Manufacturer data with selection guidance for buyers.
Manufacturer data
Published specifications
LX-F40-S1-A is a Langxin robot finishing spindle. Its exact published table row lists 1 kW spindle power, 0.6 Nm torque and 4.2 kg tool mass. Review contact direction, installed wrist load, compatible drive, abrasive limits and a representative deburring trial. Supplier values do not establish surface finish, tool life or the delivered cell scope.
- Motor power
- 1 kW
- Tool torque
- 0.6 N·m
- Tool mass
- 4.2 kg
Values and units are shown as the manufacturer publishes them. Confirm the fit for your complete cell with the manufacturer.
Use the torque difference to design a cut, not predict a finish
The A model row lists 1 kW, 0.6 Nm and 4.2 kg, versus 0.5 kW, 0.3 Nm and 4 kg for LX-F40-S1. Its speed column is lower, 24,000 versus 30,000 as printed, and its voltage and frequency columns also differ. It is therefore not a power-only replacement using unchanged drive settings. Define cutter diameter, engagement and the proposed spindle drive together. Higher listed torque does not establish burr removal rate, surface roughness or immunity to chatter on a thin wall.
Record scope: [S1]
Read the exact model row with its limits
| Published item / decision | How to use it | Limit to confirm |
|---|---|---|
| Spindle power | 1 kW | Printed supplier value; continuous-duty conditions and drive scope require confirmation. |
| Listed torque | 0.6 Nm | No torque-versus-speed curve or measured cutting result established. |
| Listed tool mass | 4.2 kg | Not the complete installed robot-wrist load. |
| Spindle size column | 40 | Printed catalog figure; dimensional units and fit require the signed drawing. |
| Spindle voltage / frequency | 200 / 800 as printed | Table units and compatible drive must be confirmed; not a facility mains specification. |
| Speed / current columns | 24,000 / 5 as printed | Confirm units, operating limits and duty with the drive supplier. |
| Compliance arrangement | radial and axial family configuration; exact usable compliance requires confirmation | Pneumatic adjustment is not evidence of calibrated closed-loop force control. |
| Force accuracy / finished surface | Not established | No measured force tolerance, roughness, burr limit or process capability is asserted. |
Record scope: [S1]
Resolve this configuration before ordering
Record scope: [S1]
Turn a sample trial into an acceptance record
- Supply representative parts including the hardest burr, smallest clearance and high/low incoming geometry; define the accepted edge or surface measurement.
- Record cutter or brush type, permissible speed, mounting, air regulation, drive settings and the complete tool assembly used in the trial.
- Measure residual burr, edge break and unintended material removal after the agreed path; record rejects, chatter, tool changes and manual interventions.
- Repeat with a worn consumable and after a stop or exchange; agree on changeover, restart and fault-recovery acceptance.
- Freeze the successful recipe and responsibilities for robot, spindle drive, air regulation, extraction, guarding, fixture and consumables.
Record scope: [S1]
Use symptoms to narrow the investigation
| Published item / decision | How to use it | Limit to confirm |
|---|---|---|
| Uneven edge or remaining burr | Compare contact direction, part variation and available compliance against the programmed path. | Stop the trial if compliance bottoms; do not compensate blindly by increasing air pressure or dwell. |
| Chatter or tool marks | Check fixture stiffness, cutter engagement, spindle-drive settings and tool balance. | The motor power rating cannot identify the cause or guarantee a finish. |
| Hot motor, drive trip or unstable contact | Review load, duty, cooling, air stability and the selected drive together. | Use supplier operating limits; the source does not define a continuous-duty envelope. |
Record scope: [S1]
Separate the spindle from the complete finishing cell
The pictured supplier tool is not a complete robot system. Ask whether the quote includes the spindle drive, mounting adapter, air regulation, tool holder, cutter or brush, changing hardware and commissioning. The illustration does not establish accessory supply or compatibility with a particular robot.
Define rotating-tool containment, guarding, dust or chip extraction, electrical protection and safe recovery for the actual material and cell. Compliance does not make sharp or rotating tools safe for unguarded human access. No certified cell, robot safety function, material-removal test, tool-life result or third-party expert approval is claimed.
Record scope: [S1]
Keep these questions in the quotation
Does this table prove a finished-surface result?
No. The values describe a supplier-published tool. Burr removal, roughness and tool life require the selected part, fixture, abrasive and recipe to be tested.
Is the published mass the load for robot selection?
No. The row lists 4.2 kg for the tool; add the adapter, holder, consumable and routed services, then review centre of gravity, moments and acceleration.
Are the drive and changing hardware included?
The published model row does not establish the delivered system scope. Require an itemized configuration, drawings, compatible drive settings and responsibility for installation.
Record scope: [S1]
Your inputs · local calculation
Build the complete mounted-mass schedule
The recorded finishing tool contributes 4.2 kg. Add components once: exclude this fixed mass from your inputs. The result is robot-mounted mass, not a statement that the changer or robot permits this load.
Enter your project inputs to calculate. No inputs are uploaded or saved.
Formula: recorded component mass + additional tooling + adapters/other equipment + retained workpiece. No automatic rating pass/fail; moments, load centre, acceleration and model-specific conditions need review.
Make the next conversation useful
Your inquiry checklist
Use the model-specific questions above to prepare one consistent brief. The checked items are temporary notes on this page; they are not submitted or saved to an account.
The carry button temporarily keeps your outline in this browser tab for up to two minutes and consumes it on the matching form. Nothing is sent until you submit the form.
Add this product to a specification comparison →Sources and check dates
[S1] Langxin LX-F40-S1-A official model page and illustrated specification table
Manufacturer publication · Source reviewed
Exact model row manually read in the official raster specification sheet; original image checksum retained privately. Supplier claims, not independently tested performance.
Background guides explain the equipment type in general. For this model, request current configuration documents, commercial scope and an application trial. How profiles are reviewed · Buyer questions