Compare 
Sign inProduct decision guide · Cartesian robots
STCW-1800 Injection Molding Robot
STCW-1800: interpret the published 25 kg load, 1800 mm vertical travel and press range alongside installation, tooling and acceptance requirements.
Manufacturer data with selection guidance for buyers.
Manufacturer data
Published specifications
STCW-1800 is a SHIP telescopic Cartesian extraction robot listed for injection-moulding applications. Its official table states 25 kg maximum load, 1800 mm vertical and 1380 mm crosswise travel, and a 700-1250 ton press screening range. Confirm the exact mounting drawing, full tooling load, machine interlocks and representative extraction trial before ordering. The illustration is for the family; catalog timing does not establish a completed production cycle.
- Payload
- 25 kg
- Vertical stroke
- 1800 mm
- Crosswise stroke
- 1380 mm
Values and units are shown as the manufacturer publishes them. Confirm the fit for your complete cell with the manufacturer.
Resolve the alternate traverse figure first
This model is listed with 1,800 mm vertical and 1,380 mm crosswise travel, a 25 kg maximum load and an 850 kg net mass. The official table writes traverse as 2,730 mm with 3,210 mm in parentheses, without explaining the configuration distinction. That ambiguity affects the machine-to-conveyor layout and foundation envelope. Keep both figures in the quotation discussion, and obtain a configuration-specific drawing before using either in the installation plan. The 700–1,250 ton press range remains a screening range, not an approved press list.
Record scope: [S1]
The published values and what they mean
| Published item / decision | How to use it | Limit to confirm |
|---|---|---|
| Maximum load | 25 kg | Supplier table; attached tooling, moments and motion conditions require approval. |
| Press screening range | 700-1250 ton | Not a machine-specific compatibility approval. |
| Vertical / crosswise travel | 1800 / 1380 mm | Linear strokes, not arm radius. |
| Traverse travel | 2730 (3210) mm | Parenthesized alternative needs a configuration drawing. |
| Arm / drive | telescopic / X.Y.Z AC Servo | Confirm controller and ordered servo arrangement. |
| Posture | 90° | Catalog label; posture mechanism and axis-count definition need confirmation. |
| Minimum take-out | 2.7 seconds | Catalog minimum, not a complete measured production cycle. |
| Air / electrical supply | 0.5Mpa / AC220V | Confirm inlet requirements, protection, electrical load and installation circuit. |
| Air usage | 4 nl | Measurement conditions and cycle basis are not defined on the page. |
| Net mass | 850 kg | Installation reactions and foundation requirements remain separate. |
Record scope: [S1]
Resolve this model’s installation questions
Record scope: [S1]
Turn the take-out claim into a test
The source lists 2.7 seconds minimum take-out. Use a loaded process trial, including mould-clear confirmation and failed vacuum/grip recovery, rather than extending this figure into an hourly-output promise.
Agree on the mould-open, robot-entry, gripping, mould-clear and placement events in the controller log. Include stops, rejected parts and manual interventions in any capacity measurement. The source does not establish absolute positioning accuracy, repeatability, safety integrity level or a certified robot–press interface.
Record scope: [S1]
Freeze the machine and handover scope
- Identify the press, mould, open gap, ejector sequence, discharge point and ordered robot mounting drawing.
- Agree on the loaded tool drawing, fixture retention, vacuum or grip monitoring and fault recovery before a trial.
- Document press–robot interlocks, access protection, stopping behaviour and permitted manual recovery for the complete cell.
- Run the representative extraction sequence and archive event logs, accepted/rejected counts and agreed acceptance limits.
- Receive wiring, pneumatic, mechanical and controller backup documents, maintenance intervals, spare-part responsibilities and installation support terms.
Record scope: [S1]
What should remain open in the quotation?
Is the picture the exact ordered robot?
The image illustrates the STCW family. A signed model-specific configuration drawing and accessory list should govern the order, not the shared illustration.
Does the press tonnage range guarantee fit?
No. Nominal clamping tonnage does not define mould geometry, mounting interface, tooling clearance or safety integration. Check the particular press and mould.
Are price, cycle savings or safety certification verified?
No such result is asserted here. The table is supplier-published information and the checks are platform procurement guidance. No independent test, expert sign-off or certificate verification is claimed.
Record scope: [S1]
Configuration worksheet
A model-specific worksheet has not been reviewed for this record. Use the inquiry outline to request the configuration and acceptance data.
Make the next conversation useful
Your inquiry checklist
Use the model-specific questions above to prepare one consistent brief. The checked items are temporary notes on this page; they are not submitted or saved to an account.
The carry button temporarily keeps your outline in this browser tab for up to two minutes and consumes it on the matching form. Nothing is sent until you submit the form.
Add this product to a specification comparison →Sources and check dates
[S1] SHIP STCW official model table and dimension sheet
Manufacturer publication · Source reviewed
Exact STCW-1800 row and published family dimensions; merged table cells expanded from DOM rowspan. Supplier claims only, no independent performance trial.
Background guides explain the equipment type in general. For this model, request current configuration documents, commercial scope and an application trial. How profiles are reviewed · Buyer questions