Compare 
Sign inProduct decision guide · Cartesian robots
STCW-2000 Injection Molding Robot
STCW-2000: interpret the published 25 kg load, 2000 mm vertical travel and press range alongside installation, tooling and acceptance requirements.
Manufacturer data with selection guidance for buyers.
Manufacturer data
Published specifications
STCW-2000 is a SHIP telescopic Cartesian extraction robot listed for injection-moulding applications. Its official table states 25 kg maximum load, 2000 mm vertical and 1380 mm crosswise travel, and a 800-1600 ton press screening range. Confirm the exact mounting drawing, full tooling load, machine interlocks and representative extraction trial before ordering. The illustration is for the family; catalog timing does not establish a completed production cycle.
- Payload
- 25 kg
- Vertical stroke
- 2000 mm
- Crosswise stroke
- 1380 mm
- Traverse stroke
- 3210 mm
Values and units are shown as the manufacturer publishes them. Confirm the fit for your complete cell with the manufacturer.
More vertical travel within the 25 kg family
STCW-2000 lists 2,000 mm vertical travel, 1,380 mm crosswise travel and 3,210 mm traverse. The STCW-1800 record has the same 25 kg load and crosswise travel, so the extra 200 mm vertical stroke does not solve an approach problem caused by insufficient crosswise motion. The listed net mass rises to 950 kg and the advertised press range is 800–1,600 ton. Review the mounting and clearance drawings with the press supplier, especially where the tool must pass an elevated mould or reach a lower discharge station.
Record scope: [S1]
The published values and what they mean
| Published item / decision | How to use it | Limit to confirm |
|---|---|---|
| Maximum load | 25 kg | Supplier table; attached tooling, moments and motion conditions require approval. |
| Press screening range | 800-1600 ton | Not a machine-specific compatibility approval. |
| Vertical / crosswise travel | 2000 / 1380 mm | Linear strokes, not arm radius. |
| Traverse travel | 3210 mm | Check the actual release point and guarding. |
| Arm / drive | telescopic / X.Y.Z AC Servo | Confirm controller and ordered servo arrangement. |
| Posture | 90° | Catalog label; posture mechanism and axis-count definition need confirmation. |
| Minimum take-out | 2.8 seconds | Catalog minimum, not a complete measured production cycle. |
| Air / electrical supply | 0.5Mpa / AC220V | Confirm inlet requirements, protection, electrical load and installation circuit. |
| Air usage | 4 nl | Measurement conditions and cycle basis are not defined on the page. |
| Net mass | 950 kg | Installation reactions and foundation requirements remain separate. |
Record scope: [S1]
Resolve this model’s installation questions
Record scope: [S1]
Turn the take-out claim into a test
The quoted minimum take-out is 2.8 seconds. Agree on whether the measure includes gripping and robot-clear verification, then test the intended mould and workpiece rather than an empty motion demonstration.
Agree on the mould-open, robot-entry, gripping, mould-clear and placement events in the controller log. Include stops, rejected parts and manual interventions in any capacity measurement. The source does not establish absolute positioning accuracy, repeatability, safety integrity level or a certified robot–press interface.
Record scope: [S1]
Freeze the machine and handover scope
- Identify the press, mould, open gap, ejector sequence, discharge point and ordered robot mounting drawing.
- Agree on the loaded tool drawing, fixture retention, vacuum or grip monitoring and fault recovery before a trial.
- Document press–robot interlocks, access protection, stopping behaviour and permitted manual recovery for the complete cell.
- Run the representative extraction sequence and archive event logs, accepted/rejected counts and agreed acceptance limits.
- Receive wiring, pneumatic, mechanical and controller backup documents, maintenance intervals, spare-part responsibilities and installation support terms.
Record scope: [S1]
What should remain open in the quotation?
Is the picture the exact ordered robot?
The image illustrates the STCW family. A signed model-specific configuration drawing and accessory list should govern the order, not the shared illustration.
Does the press tonnage range guarantee fit?
No. Nominal clamping tonnage does not define mould geometry, mounting interface, tooling clearance or safety integration. Check the particular press and mould.
Are price, cycle savings or safety certification verified?
No such result is asserted here. The table is supplier-published information and the checks are platform procurement guidance. No independent test, expert sign-off or certificate verification is claimed.
Record scope: [S1]
Configuration worksheet
A model-specific worksheet has not been reviewed for this record. Use the inquiry outline to request the configuration and acceptance data.
Make the next conversation useful
Your inquiry checklist
Use the model-specific questions above to prepare one consistent brief. The checked items are temporary notes on this page; they are not submitted or saved to an account.
The carry button temporarily keeps your outline in this browser tab for up to two minutes and consumes it on the matching form. Nothing is sent until you submit the form.
Add this product to a specification comparison →Sources and check dates
[S1] SHIP STCW official model table and dimension sheet
Manufacturer publication · Source reviewed
Exact STCW-2000 row and published family dimensions; merged table cells expanded from DOM rowspan. Supplier claims only, no independent performance trial.
Background guides explain the equipment type in general. For this model, request current configuration documents, commercial scope and an application trial. How profiles are reviewed · Buyer questions