Compare 
Sign inProduct decision guide · Cartesian robots
STDW-2500 Injection Molding Robot
STDW-2500: interpret the published 35 kg load, 2500 mm vertical travel and press range alongside installation, tooling and acceptance requirements.
Manufacturer data with selection guidance for buyers.
Manufacturer data
Published specifications
STDW-2500 is a SHIP telescopic Cartesian extraction robot listed for injection-moulding applications. Its official table states 35 kg maximum load, 2500 mm vertical and 1950 mm crosswise travel, and a 1600-3000 ton press screening range. Confirm the exact mounting drawing, full tooling load, machine interlocks and representative extraction trial before ordering. The illustration is for the family; catalog timing does not establish a completed production cycle.
- Payload
- 35 kg
- Vertical stroke
- 2500 mm
- Crosswise stroke
- 1950 mm
Values and units are shown as the manufacturer publishes them. Confirm the fit for your complete cell with the manufacturer.
Choose the extra stroke for a measured constraint
The STDW-2500 entry lists 2,500 mm vertical and 1,950 mm crosswise travel, compared with 2,200 and 1,700 mm on STDW-2200. Both list 35 kg maximum load, so the choice is chiefly about the required mould and discharge geometry rather than increased payload. Its traverse entry is 3,500 mm with 4,000 mm in parentheses; the configuration difference is not explained in the published table. With 1,800 kg listed net mass and a 1,600–3,000 ton press screening range, installation support and the selected long-traverse option must be resolved together.
Record scope: [S1]
The published values and what they mean
| Published item / decision | How to use it | Limit to confirm |
|---|---|---|
| Maximum load | 35 kg | Supplier table; attached tooling, moments and motion conditions require approval. |
| Press screening range | 1600-3000 ton | Not a machine-specific compatibility approval. |
| Vertical / crosswise travel | 2500 / 1950 mm | Linear strokes, not arm radius. |
| Traverse travel | 3500 (4000) mm | Parenthesized alternative needs a configuration drawing. |
| Arm / drive | telescopic / X.Y.Z AC Servo | Confirm controller and ordered servo arrangement. |
| Posture | 90° | Catalog label; posture mechanism and axis-count definition need confirmation. |
| Minimum take-out | 3.5 seconds | Catalog minimum, not a complete measured production cycle. |
| Air / electrical supply | 0.5Mpa / AC220V | Confirm inlet requirements, protection, electrical load and installation circuit. |
| Air usage | 6 nl | Measurement conditions and cycle basis are not defined on the page. |
| Net mass | 1800 kg | Installation reactions and foundation requirements remain separate. |
Record scope: [S1]
Resolve this model’s installation questions
Record scope: [S1]
Turn the take-out claim into a test
The listed minimum take-out is 3.5 seconds. Compare it with STDW-2200 only using equivalent load, travel and signal definitions; extra travel does not guarantee more output.
Agree on the mould-open, robot-entry, gripping, mould-clear and placement events in the controller log. Include stops, rejected parts and manual interventions in any capacity measurement. The source does not establish absolute positioning accuracy, repeatability, safety integrity level or a certified robot–press interface.
Record scope: [S1]
Freeze the machine and handover scope
- Identify the press, mould, open gap, ejector sequence, discharge point and ordered robot mounting drawing.
- Agree on the loaded tool drawing, fixture retention, vacuum or grip monitoring and fault recovery before a trial.
- Document press–robot interlocks, access protection, stopping behaviour and permitted manual recovery for the complete cell.
- Run the representative extraction sequence and archive event logs, accepted/rejected counts and agreed acceptance limits.
- Receive wiring, pneumatic, mechanical and controller backup documents, maintenance intervals, spare-part responsibilities and installation support terms.
Record scope: [S1]
What should remain open in the quotation?
Is the picture the exact ordered robot?
The image illustrates the STDW family. A signed model-specific configuration drawing and accessory list should govern the order, not the shared illustration.
Does the press tonnage range guarantee fit?
No. Nominal clamping tonnage does not define mould geometry, mounting interface, tooling clearance or safety integration. Check the particular press and mould.
Are price, cycle savings or safety certification verified?
No such result is asserted here. The table is supplier-published information and the checks are platform procurement guidance. No independent test, expert sign-off or certificate verification is claimed.
Record scope: [S1]
Configuration worksheet
A model-specific worksheet has not been reviewed for this record. Use the inquiry outline to request the configuration and acceptance data.
Make the next conversation useful
Your inquiry checklist
Use the model-specific questions above to prepare one consistent brief. The checked items are temporary notes on this page; they are not submitted or saved to an account.
The carry button temporarily keeps your outline in this browser tab for up to two minutes and consumes it on the matching form. Nothing is sent until you submit the form.
Add this product to a specification comparison →Sources and check dates
[S1] SHIP STDW official model table and dimension sheet
Manufacturer publication · Source reviewed
Exact STDW-2500 row and published family dimensions; merged table cells expanded from DOM rowspan. Supplier claims only, no independent performance trial.
Background guides explain the equipment type in general. For this model, request current configuration documents, commercial scope and an application trial. How profiles are reviewed · Buyer questions